Want to completely erase all configurations from your Holosun EPS Carry Red Dot? A factory reset is the way to go. This process clears any custom adjustments you've made, returning it to its default state. If you're experiencing problems with your red dot or simply want a fresh start, here's how to perform a factory reset.
- First turning off the Holosun EPS Carry Red Dot.
- After that, find the small reset button on the side of the device. It's usually hidden within a recessed area.
- Apply a thin object, like a paperclip or pin, to gently push and hold the reset button.
- Simultaneously, turn the red dot back on.
- You're going to a brief flashing sequence or indicator that confirms the reset process has begun.
- Stop pressing the reset button once the sequence ends.
- Your Holosun EPS Carry Red Dot is now back to its factory settings.
Adjusting Your Holosun EPS Carry to Default Settings
If your Holosun EPS Carry red dot sight isn't behaving as expected, resetting it to the factory default settings may correct the difficulty. This process is relatively simple and can be achieved in a few minutes. First, locate the small adjustment button on the side of the sight. Use a fine-tipped object, like a paperclip or pencil, to press and depress the button for several how to factory reset Holosun EPS Carry red dot seconds. You should see a rapid indication on the sight's display indicating that the reset is successful.
After the reset is complete, your EPS Carry will be back to its original settings. This means that all previous modifications, such as brightness level and reticle type, will be restored. Now you can test that the sight is functioning appropriately.
Restore Your Holosun EPS Carry To Factory {Defaults|Configurations|
If you've been tinkering with your Holosun EPS Carry and want to return it to its original state, returning it to factory defaults is a simple process. This will eliminate any custom settings you've made, restoring the sight to its original configuration straight out of the box. To accomplish this, locate the small button on the side of your Holosun EPS Carry. Using a thin object like a paperclip or a pen, depress the reset switch for a few seconds until you see a visual indication that the sight has been recalibrated. Release the button and your Holosun EPS Carry will be back to its factory settings, ready for accurate shooting.
Revert to Original Configuration for Holosun EPS Carry Red Dot Sight
To execute a factory reset on your Holosun EPS Carry Red Dot Sight, you will need to utilize the sight's internal settings system. Begin by turning on the sight. Then, find the switch used to adjust through the screens.
Once you have identified the correct button, {press{ and hold it for a designated amount of time. This will usually activate the reset function. You may witness a short flashing light or sequence on the sight's screen, indicating that the reset is complete.
After the reset, your Holosun EPS Carry Red Dot Sight will return to its original settings. You may need to recalibrate the sight after the reset process is completed.
Restore a Holosun EPS Carry Red Dot
To initiate a hard reinitialization on your Holosun EPS Carry red dot sight, you'll need to locate the tiny lever situated on the rear/bottom/side of the device. Using a small tool/object/item, gently depress and hold the button/switch/lever down for approximately 15 seconds. During this duration/time/period, you might see a blinking/flashing indicator light on the sight, signaling that the reinitialization process is in progress/motion/execution. After removing your finger/tool/object from the button/switch/lever, the red dot should return to normal operation/be reset/restart.
Remember, a hard reset will restore/return/set back your Holosun EPS Carry to its factory settings/defaults/configurations. This means/implies/suggests that any customizations/adjustments/modifications you had previously made will be lost/erased/removed.
Return Your Holosun EPS Carry to Factory Settings Quickly
Restoring your Holosun EPS Carry to its factory settings is a straightforward process that can be completed in just a few simple steps. First, ensure the device is powered off and remove the battery pack. Then, locate the small reset button on the side of the unit. Apply a thin object, such as a pen or paperclip, to press and hold the reset button for approximately 10 seconds. Release the button and reinsert the battery pack. Your Holosun EPS Carry should now be reset to its original factory settings.
- Check that all settings have been Reset to default by reviewing the display menu.
Success! Your Holosun EPS Carry is now ready for use with its factory configurations.